Skip to product information
1 of 1

6 Hour Relay Team Dayglo Numbers & Letters (Now use K-2 Numbers)

6 Hour Relay Team Dayglo Numbers & Letters (Now use K-2 Numbers)

Scarcella Designz

Regular price $0.00
Regular price Sale price $0.00
Sale Sold out
Shipping calculated at checkout.

6 Hour Relay ONLY Mandatory Identification Competition Dayglo Number/s

Size: 150mm high

Number/s are made to 6 Hour Relay regulations. Scarcella Designz takes no responsibility for incorrectly purchased items.  To double check your requirements, please check out the latest 6 Hour Relay 2020 Supplementary Regulations.

Please select your team Number, then your driver Number.

View full details

Fluro Vinyl Features

Vinyl Specifications

This vinyl is 120 micron film that is suitable for high visability safety and promotional signage.  The external application has a lifespan of 3 to 6 months.

Face Film

Face Film: Polymeric calendered PVC 
Gauge: 120 micron nominal 

Adhesive

Type Solvent free acrylic  removable
Application temperature +5°C to +60°C 
Service temperature -30°C to +110°C

Release Liner

Durability

External weathering 6 months exterior use

Application Guidelines

May be applied with a wet or dry application.

 Apply unstressed, in particular to curves and recesses. It is not suitable for application over rivets or complex recesses.

 Not recommended for use on low energy surfaces such as polypropylene.

Application Temperature

In cold conditions vinyl can make application difficult, as the initial adhesion of the vinyl will be reduced and the time taken for the adhesive to cure completely will be longer.

The recommended application temperature for applying vinyl using a ‘dry application method’ is at least 10 Degrees and for a ‘wet application method’ is at least 17 Degrees.  Application in temperatures below 5 Degrees is not recommended.

When applying vinyl graphics to a vehicle in cold weather always try to work indoors and raise the temperature of the vehicle by using a fan heater inside with the vehicle doors open.  When this is not possible, for example an exterior application in winter conditions, it is very important to make absolutely sure that the adhesive has established a good bond to the substrate.

Aligning and Applying Sign Vinyl Decals

Apply a 50mm tab of masking tape to fix each in place horizontally.  Apply a third strip of masking tape vertically across the centre from top to bottom; the tape should extend above and below the decal and fix it to the substrate.

Start with the right hand side of the decal and cut or tear the 50mm strip of masking tape, leaving half on the substrate.  Turn the right hand side of the graphic back on itself.  Peel away the silicone release liner, cutting it at the centre point where the vertical masking tape fixes the decal to the substrate, and discard.  When peeling decals away from the silicone release liner always try to keep them as flat as possible and peel back the release liner towards you.  This will reduce the chance of damage to fine details or serifs.

The first half of the decal can now be lightly applied by holding it taught and using the two parts of the 50mm masking tape tab to align it perfectly.  Squeegee down firmly.

Remove the vertical strip of masking tape and repeat for the left hand side of the decal.

Finally remove the application tape by peeling away at 45 Degrees to the direction of the text and 180 Degrees to the surface.

Air bubbles can be removed by puncturing with the tip of a scalpel.

This method of application can be modified for large graphics (in excess of 2m).  Apply vertical stripes of masking tape at two, three or more intervals.  Cut the graphic half way between these points to form smaller panels and proceed as described above.

Care Instructions

Please refrain from washing you car or leaving it in the rain in the first 5 days after installation due to the adhesive still needing to stick correctly.  Car wash or cleaning products will hinder the process.

For a short amount of time that the vinyl/wrap is still curing, you may notice bubbles.  These should start to disappear from regular drivingorbeing exposed to sunlight.  It can take a few weeks, depending on how the signage is used.

It is recommended when washing the vinyl/wrap that a PH neutral product is used.

If using a pressure washer, please insure that you keep the spray at least 1 metre away from the surface as the pressure may lift the edges of the vinyl/wrap.

Do not use abrasive or resin based products as it can cause a haze.

Shipping

DELIVERY TIME FRAMES

The nature of print is that our processing, production and postage time frames can vary, though we do our best to ensure the quickest turnaround on each order. We ship using Australia Post, and we are not responsible for any delays caused by the courier.

Please contact us so we can look after you, well before your due date. We want you to receive your garments on time and are only a phone call or an email away.

Returns

RETURNS POLICY

We work hard to provide consistent, quality prints for our customers, however, if you're unhappy with the product you receive, please follow these instructions to return/receive a new product: Email us at simone@scarcelladesignz.com with;

The date of your purchase, Your order number, What you would like to return, Why you want to return it, A photo highlighting the fault/damage

Once we have received this email we will review the request and advise the outcome. You may have to return the product back to us at your own postage cost if required. 

WHAT CAN BE RETURNED

Only items that are faulty, damaged or have a faulty print may be returned. Once an order has been placed using our online system, it's immediately added to our production queue, and we can't edit or cancel it once it's been placed. No returns are accepted after 14 days of your order being received. We do not accept items that have noticeable wear or makeup stains. We do not refund or warranty BYO or supplied garments, supplying garments to us is done at your own risk. Returns must also comply with our user agreement.

We do not refund or exchange for change of mind, errors in approved proofs, errors from non 'print-ready' artwork, shipping or supplier stock delays or if the customer chooses the wrong garment size. Please note: sizing measurements online are within +-2cm—anything outside of this allowance is considered faulty. Print dimensions and print placement measurements are within +-2cm and anything outside of this can be considered faulty. Proof approval is important, and paying for an order is considered approval of the supplied proof. 

Clients must ensure that the artwork, quantity and shipping address is correct before payment is made. We do not accept returns for errors made by any of our couriers when we have dispatched to the correct address by the due date.

BYO & SUPPLIED GARMENTS

BYO supplied garments & apparel are supplied at the customer’s risk.  There is no warranty on the print added to the garment.

Please remember that if a print or production error occurs on BYO apparel, replacement items will not be sourced by us & will not reimburse. If you have concerns regarding BYO apparel, it is suggested that you either supply extra garments for testing purposes, or instead choose items from our product range.