Bunny Wall Decal

Vinyl Product Description:

Soft PVC film which conforms well with the substrate.  For indoor applications such as markings, inscriptions and decorations applied to wall surfaces

Face Film

Gauge: 80 micron
Tensile Strength min. 19 MPa
Elongation at break Along min. 130%, Across min. 150% 

Adhesive

Type Polyacrylate
Application temperature > +10°C

Release Liner

Type Silicone coated paper on one side

Durability

Removability Removable from most surfaces without residue.
Fire Rating DIN EN 13501-1 B-s2, d= (flame retardant, limited smoke, no draining)
Service life by specialist application (Indoor Use) 2 years

Clean the surface right before lamination because dust and other suspended particles may quickly stick to the surface. The best cleaning results are achieved with a dry and a non-fuzzing microfibre cloth. Please watch out particularly for areas where angles and edges of the graphics will be.

The film is applied in a dry state.

 Surfaces to which the material will be applied must be thoroughly cleaned and free from dust, grease or any other contamination that could affect the adhesion of the material.

 Freshly lacquered or painted surfaces should be allowed to dry for at least three weeks and to completely cure.

 The compatibility of selected lacquers and paints should be tested by the user, prior to application of the material.

 Not recommended for surfaces such as: • roughly structured surface • Concrete, cement wall, unpainted plaster • freshly painted surfaces (not dried) • areas with dirt-repellent surface • moist room walls (e.g. bathroom, garage) or even just damp walls • dirty walls (e.g. nicotine, fat) • hard-to-stick surfaces (e.g. old wall paper) 

Environment and surface temperature must be at least + 20° C before these films can be removed. Using a knife, first lift up cautiously one corner of the film. Then slowly draw the film from the surface at a 180° angle. Heating the film with a hot-air gun while pulling makes removal considerably easier. If the film being removed is very old, a small amount of residue from the adhesive may remain on the surface. It can be removed easily with varnish thinner.

Do not use chemicals or abrasives on your decals as it damage you decal.

DELIVERY TIME FRAMES

The nature of print is that our processing, production and postage time frames can vary, though we do our best to ensure the quickest turnaround on each order. We ship using Australia Post, and we are not responsible for any delays caused by the courier.

Please contact us so we can look after you, well before your due date. We want you to receive your garments on time and are only a phone call or an email away.

RETURNS POLICY

We work hard to provide consistent, quality prints for our customers, however, if you're unhappy with the product you receive, please follow these instructions to return/receive a new product: Email us at simone@scarcelladesignz.com with;

The date of your purchase, Your order number, What you would like to return, Why you want to return it, A photo highlighting the fault/damage

Once we have received this email we will review the request and advise the outcome. You may have to return the product back to us at your own postage cost if required. 

WHAT CAN BE RETURNED

Only items that are faulty, damaged or have a faulty print may be returned. Once an order has been placed using our online system, it's immediately added to our production queue, and we can't edit or cancel it once it's been placed. No returns are accepted after 14 days of your order being received. We do not accept items that have noticeable wear or makeup stains. We do not refund or warranty BYO or supplied garments, supplying garments to us is done at your own risk. Returns must also comply with our user agreement.

We do not refund or exchange for change of mind, errors in approved proofs, errors from non 'print-ready' artwork, shipping or supplier stock delays or if the customer chooses the wrong garment size. Please note: sizing measurements online are within +-2cm—anything outside of this allowance is considered faulty. Print dimensions and print placement measurements are within +-2cm and anything outside of this can be considered faulty. Proof approval is important, and paying for an order is considered approval of the supplied proof. 

Clients must ensure that the artwork, quantity and shipping address is correct before payment is made. We do not accept returns for errors made by any of our couriers when we have dispatched to the correct address by the due date.

BYO & SUPPLIED GARMENTS

BYO supplied garments & apparel are supplied at the customer’s risk.  There is no warranty on the print added to the garment.

Please remember that if a print or production error occurs on BYO apparel, replacement items will not be sourced by us & will not reimburse. If you have concerns regarding BYO apparel, it is suggested that you either supply extra garments for testing purposes, or instead choose items from our product range.